Self-polishing high-performance antifouling paint without organic tin antifouling agent composed of special antifouling agent, cuprous oxide, self-polishing copolymerization resin and so on.
Key Features
· Long-term prevention of fouling of barnacles, oysters, limestone insects, bryozoans and algae and other marine attachments to the bottom of the bilge to keep the ship clean and speed is not affected
* Special anti-fouling agent and self-polishing copolymer resin, free of organic tin, with self-polishing effect
· Construction convenient, can use no gas high-pressure spraying, brushing or roller coating and other different methods of construction. No air high pressure spray a dry film thickness of up to 100mm
· When the film thickness reaches the specified requirements, the antifouling effective period can reach more than two years
Uses Applicable to marine facilities such as ship's bottom, wharf, navigation mark, seawater gate and so on. It is used as anti-fouling paint to prevent marine bio-fouling.
Appearance reddish-brown, no light
Construction parameters
Volume of solid 52 ± 3% (according to GB / T9272 eqv ISO3233: 1998 provisions of the determination)
Dry film thickness 50-100mm
Wet film thickness 96-192mm
The theoretical amount of 211-422g / m2
A flash point of 28 ° C
Drying time
| temperature | 5℃ | 20℃ | 30℃ |
| Table dry | 4h | 2h | 1h |
| Hard work | 36h | 24h | 16h |
Overcoating interval time
| temperature | 5℃ | 20℃ | 30℃ |
| The shortest | 36h | 16h | 8h |
| longest | 15d | 15d | 15d |
It is recommended that the number of coating channels for the number of anti-fouling paints, that is, the dry film thickness, may vary depending on the docking time of the ship. The number of coating passes or the thickness of the coating increases with the maintenance interval. Suggested as follows:
| Docking interval （月） | Airless Spray Dry Film Thickness（mm）×Road number* | Anti-fouling paint dry film total thickness （mm） |
| 12 | 50×2 | 100 |
| 24 | 70×3 | 210 |
* The recommended number of coating is no air painting when the number of road, airless spray a film thickness equivalent to brush or roller 2-3. If the use of brush or roller, as long as the required film thickness can be achieved, the number of coating Road is not limited to the recommended number of channels.
Supporting system
846-1 epoxy asphalt thick slurry antirust paint (or 615-1 aluminum powder chlorinated rubber antirust paint) 125mm
846-2 Epoxy Asphalt Thick Antirust Paint (or 615-2 Aluminum Chlorinated Rubber Antirust Paint) 125mm
Chlorinated rubber iron red thick slurry antirust paint 60mm
Self - polishing antifouling paint
Surface treatment
· Before painting the antisepsis paint, the bottom steel plate should be treated by sandblasting to Sa2.5 level; or remove the old paint film and wind or electric elastic grinding wheel to St3 level
· Before removing all the contaminants such as oil, dust and so on, the paint must be dry
Construction conditions · Substrate temperature should be above 3 ℃ above dew point
· Relative humidity not more than 85%
Coating method
Airless spray
Thinner 102 thinner
Dilution 0-5% (by weight of paint)
Nozzle diameter 0.4-0.5mm
The discharge pressure is 15 to 30 MPa (about 150 to 300 kg / cm2)
Brush / roller
Thinner 102 thinner
Dilution 0-3% (by weight of paint)
Cleaner 102 thinner
For safety measures, refer to the Material Safety Data Sheet (MSDS) of Anhui Kailin New Material Co., Ltd.
Packaging 10L barrels 20kg
Shelf life of 12 months
Remark For the correct use of our products, please carefully read the "User's Guide" in this manual.
Statement The above data and data are based on our test and practical experience in the use of accumulated and can be used as a construction guide. We do not understand the situation in the construction, we only guarantee the quality of the paint itself, other issues will not be responsible. For this manual, we will be based on the continuous improvement of products have the right to modify.
If you have questions, you can：
