<address id="9hx9l"></address>
      <form id="9hx9l"></form>
        <form id="9hx9l"></form>

        <form id="9hx9l"></form>

          Back

          F04-1£¨751£©Aluminum phenolic phenolic enamel

          Product introduction

          Form :
          Main characteristics :
          Purpose :
          Appearance :

          Composed of dry vegetable oil and modified phenolic resin as the base material, together with the modulation of aluminum powder with a metallic finish.

          Key Features

                         * Has a good gloss

                         ¡¤ Has good adhesion

                         ¡¤ Hard film

          Use Apply to construction, transportation, machinery and equipment, as well as indoor and outdoor all wood, metal and other surfaces for topcoat purposes.

          The appearance of aluminum, bright

          Construction parameters Group A: Group B = 4: 1 (weight ratio)

          Volume of solid 44 ¡À 3% (according to GB / T9272 eqv ISO3233: 1998 provisions of the determination)

                         Dry film thickness 35mm

                         Wet film thickness 80mm

                         Theoretical amount of 72g / m2

                         A flash point of 35 ¡ã C

                         Drying time (25 ¡æ)

                         Table dry ¡Ü 6h

                         Hard work ¡Ü 18h

                         Overcoating interval time 

          temperature5¡æ20¡æ30¡æ
          The shortest48h24h20h
          longestUnlimited

          Recommended coating number 2, dry film thickness 70mm

          712 Hongdan phenolic anti-rust paint, 725 zinc yellow phenolic antirust paint, 706 anti-rust paint, C53-38 aluminum and iron rust-proof paint and other oil, alkyd, Phenolic-type anti-rust primer.

          Surface treatment

                        • Before the paint should be completely dry

                        • Remove all oil and debris from the paint film

          Construction conditions

                        ¡¤ Before use, add aluminum paste into the paint in proportion to fully stir evenly after over 0.2mm (80 mesh)

                        • Substrate temperature should be above 3 ¡æ above dew point

                        ¡¤ Relative humidity not more than 85%

          Coating method

          Airless spray

                    Diluent 104 Diluent

                    Dilution 0-5% (by weight of paint)

                    Nozzle diameter 0.4-0.5mm

                    The discharge pressure 12-15Mpa (about 120-150kg / cm2)

          Air spraying

                        Diluent 104 Diluent

                        Dilution 0-10% (by weight of paint)

                        Nozzle diameter of 2.0-3.0mm

                        Air pressure 0.3-0.4MPa (about 3-4kg / cm2)

          Roll coating / brushing

                  Diluent 104 Diluent

                  Dilution 0-3% (by weight of paint)

          Cleaner 104 Diluent

          For safety measures, please refer to the Material Safety Data Sheet (MSDS) of Anhui Kailin New Material Co., Ltd. (formerly Tianchang Kailin Chemical Co., Ltd.).

          Packaging a group of 20L barrels 16kg

          Group B 4L barrels 4kg

          Shelf life of 12 months

          Remark For the correct use of our products, please carefully read the "User's Guide" in this manual.

          Statement The above data and data are based on our test and practical experience in the use of accumulated and can be used as construction guide. We do not understand the situation in the construction, we only guarantee the quality of the paint itself, other issues will not be responsible. For this manual, we will be based on the continuous improvement of products have the right to modify.


          If you have questions, you can£º

          Or leave a message for us.

          Related recommendation
          Online Service

          Hotline

          0550-7911368

          在线电影播放,奇米第四包,日本一区二区精品视频,一级按摩片A一级按摩

              <address id="9hx9l"></address>
              <form id="9hx9l"></form>
                <form id="9hx9l"></form>

                <form id="9hx9l"></form>