<address id="9hx9l"></address>
      <form id="9hx9l"></form>
        <form id="9hx9l"></form>

        <form id="9hx9l"></form>


          C53-38 Antirust paint

          Product introduction

          Form :
          Main characteristics :
          Purpose :
          Appearance :

          Composed of alkyd resin and phenolic paint as the base material, iron oxide red, aluminum powder and other anti-rust pigments, physical pigments, driers, additives and solvents and other components.

          Key Features

                         * Tough film, with good adhesion

                         * Dry faster

                         * Has good anti-rust performance

                         * Has good construction performance

                         • No poisonous gases are generated during welding, cutting, or firework correction

          Uses Applicable to ships above the waterline, general cabinets and general land-based steel structure for anti-rust primer.

          The appearance of silver-red, film formation, a slight brush marks.

          Construction parameters

                         Volume of solid 48 3% (according to GB / T9272 eqv ISO3233: 1998 provisions of the determination)

                         The dry film thickness is 40mm

                         Wet film thickness 83mm

                         The theoretical amount of 106g / m2

                         A flash point of 35 C

                         Drying time (25 )

                         Table dry 3h

                         Hard work 24h

          Overcoating interval time

          The shortest
          longest3 months

          Recommended coating number 2, dry film thickness greater than 80mm

          After supporting all kinds of alkyd paint or phenolic finish

          Surface treatment

                        * There are oxide steel: sandblasting to Sa2 level

                        * No oxide steel: pneumatic or electric grinding tools polished to St3 level

                        Steel coated with shop primer: paint film damage and corrosion at the second rust, polished to St3 level

                        * Welding, flame cutting or fire correction Combustion: polished to St3 level

          Construction conditions

                        • Substrate temperature should be above 3 above dew point

                        Relative humidity not more than 85%

          Coating method

          Airless spray

                    Diluent 104 Diluent

                    Dilution 0-5% (by weight of paint)

                    Nozzle diameter 0.4-0.5mm

                    The discharge pressure is 12 to 15 MPa (about 120 to 150 kg / cm2)

          Air spraying

                        Diluent 104 Diluent

                        Dilution 0-10% (by weight of paint)

                        Nozzle diameter of 2.0-3.0 mm

                        Air pressure 0.3-0.4MPa (about 3-4kg / cm2)

          Roll coating / brushing

                    Diluent 104 Diluent

                    Dilution 0-3% (by weight of paint)

          Cleaner 104 Diluent

          For safety measures, please refer to the Material Safety Data Sheet (MSDS) of Anhui Kailin New Material Co., Ltd. (formerly Tianchang Kailin Chemical Co., Ltd.).

          Packaging 20L drums 24kg

          Shelf life of 12 months

          Remark For the correct use of our products, please carefully read the "User's Guide" in this manual.

          Statement The above data and data are based on our test and practical experience in the use of accumulated and can be used as construction guide. We do not understand the situation in the construction, we only guarantee the quality of the paint itself, other issues will not be responsible. For this manual, we will be based on the continuous improvement of products have the right to modify.

          If you have questions, you can

          Or leave a message for us.

          Related recommendation
          Online Service




              <address id="9hx9l"></address>
              <form id="9hx9l"></form>
                <form id="9hx9l"></form>

                <form id="9hx9l"></form>