Composed of alkyl silicate, zinc powder and additives and other components of the two-component inorganic zinc silicate shop primer.

Key Features

             · Zinc powder with cathodic protection, excellent anti-rust performance, dry film thickness of 20μm, the maintenance period of 6-9 months

             * Fast dry, only a very short time that can carry and stack

             · Excellent welding performance and cutting performance

             · Has excellent heat resistance, the film can withstand high temperatures of 400 ℃, welding cutting the burning area is small

             · Excellent low temperature curing performance

             · Excellent solvent resistance

             * Excellent impact resistance, excellent wear resistance and moderate flexibility

             · Compatible with most paint systems

             · Type approval by China Classification Society

Uses Used in workshop pre-treatment lines such as shipyards, heavy machinery plants, steel structure processing and so on.

The appearance of gray no light

Construction parameters

              Volume solids 38 ± 3% (measured according to ISO 3233: 1998, GB / T9272 eqv) (after mixing)

              Component A: Component B = 2: 1 (weight ratio)

              Dry film thickness of 20μm

              The wet film thickness was 53 μm

              Theoretical amount of 90g / m2

              Flash point of a component (zinc slurry) 13 ℃

                              B component (main agent) 13 ℃

              Drying time (25 ℃)

                      Table dry ≤ 5min

                      Hard work ≤ 1h

Pipeline drying time (steel preheating 50 ℃, bake temperature 120 ℃) ≤ 5min

Painting interval

Minimum coating interval of 8h or more, before painting with a cloth dipped in 107 thinner wipe 704 paint film surface to determine whether the complete curing. If the zinc powder dissolved in the cloth, indicating that the film has not yet fully cured, to continue to dry; at less than 70% relative humidity, the film can be sprinkled on the water to make the film curing; dry cloth to colorless Dissolved), that the film has been cured completely before painting the next road.

The maximum coating interval is unlimited, but the zinc salt must be removed before overcoating.

Can use the time (A, B mixed)

 It is recommended to coat the number of channels without air spray 1, dry film thickness 20μm.

After supporting paint with chlorinated rubber, epoxy, epoxy asphalt, asphalt, polyurethane, ethylene and other systems supporting the use of coatings. But not with oily, alkyd, polyester paint used in supporting.

Surface treatment Steel sandblasting to Sa2.5, surface roughness 30-75μm

Construction conditions · Construction can be carried out at -20 ° C to 50 ° C

                     • When the temperature of the substrate is too high (≥40 ℃), spray gun must be used, but the temperature of the substrate should not exceed 60 ℃. In order to avoid dry spray must be adjusted to 107 thinner dry spray so far

                      • Substrate temperature should be above 3 ℃ above dew point

                      · Relative humidity not more than 85%

Coating method

Airless spray

           Diluent 107 Diluent

           Dilution 0-10% (by weight of the paint) * Note to prevent dry spray

           Nozzle diameter 0.4-0.5mm

           The discharge pressure was 15 MPa (about 150 kg / cm2)

  Air spraying

               Diluent 107 Diluent

               Dilution 0-10% (by weight of the paint) * Note to prevent dry spray

               The nozzle diameter is 2.0-2.5mm

               Air pressure 0.3-0.6MPa (about 3-6kg)

Roller / brush Large area coating is not recommended, can only be used for small area repair

                     Diluent 107 Diluent

                     Dilution 0-5% (by weight of paint)

Cleaner 107 Diluent

For safety measures, please refer to the Material Safety Data Sheet (MSDS) of Anhui Kailin New Material Co., Ltd. (formerly Tianchang Kailin Chemical Co., Ltd.).

Packing Group A (zinc paste) 20L barrels 20kg

              B component (main agent) 10L barrels 10kg

Shelf life of 6 months

Notes · During the construction of the mixer stir constantly to prevent zinc powder precipitation

                     · When the temperature is above 30 ℃, it is necessary to prevent the dry spray from adding 0-10% of the 107 diluent

                     · 704 inorganic zinc primer for the longest painting interval time is not restricted, but in the paint under the road before the paint must be completely removed from the zinc surface of the paint film formed, otherwise it will affect the film adhesion and protective effect of the interlayer

Remark For the correct use of our products, please carefully read the "User's Guide" in this manual.

Statement The above data and data are based on our test and practical experience in the use of accumulated and can be used as construction guide. We do not understand the situation in the construction, we only guarantee the quality of the paint itself, other issues will not be responsible. For this manual, we will be based on the continuous improvement of products have the right to modify.