Composed of zinc powder, epoxy resin and polyamide curing agent, additives and solvents composed of two-component thick-film epoxy zinc-rich anti-rust paint.

Key Features

              * The film contains a lot of metal zinc powder, with cathodic protection

              · Excellent anti-rust performance and durability

              · Excellent adhesion and impact resistance

              · Excellent abrasion resistance

              · Excellent salt spray resistance

              * Has a wide range of oil resistance and solvent resistance

              Dry fast

              · Can be used with most high-performance anti-rust paint and topcoat

              · Type approval by China Classification Society

Uses Used in large bridges, port machinery, heavy machinery, oil extraction and mine equipment, buried pipelines,

                 Hydraulic steel gates, plant steel structure, the outer wall of oil storage tanks, gas tank wall, the ship above the waterline hull and deck steel structure of heavy anti-corrosion system for anti-rust primer. It is the best primer for epoxy-type intermediate coat and epoxy topcoat.

The appearance of gray no light.

Construction parameters

              Volume of solid 56 ± 3% (according to GB / T9272 eqv ISO3233: 1998 provisions) (after mixing)

              Component A: Component B = 91: 9 (weight ratio)

              Dry film thickness 80mm

              Wet film thickness 143mm

              Theoretical amount of 314g / m2

              Flash point of a component (base material) 27 ℃

                            Component B (curing agent) 27 ℃

              Drying time (25 ℃)

                         Table dry ≤ 30min

                         Hard work ≤ 24h

                         Fully cured 7d

Curing time (after mixing) (25 ℃) 30min

Can use the time (A, B mixed)

* When the temperature is above 30 ℃, the pot life of Group A and B will be shortened with the temperature increasing.

Overcoating interval time

Zinc-rich primer film in the place for a long time, the surface will appear zinc salt (ie, basic zinc carbonate, also known as white rust), so in the coating after the road paint should not be long before exposure. For a longer coating interval, it is recommended as soon as possible coating 842 epoxy iron oxide antirust paint as a closed coating, in order to reduce the workload of the secondary derusting

            • In the clean indoor environment for months or in a clean outdoor environment for 14 days, the film surface does not form zinc salts. However, in the industrial atmosphere or marine climate environment, will soon produce zinc salts, so after painting the interval between the paint should be shortened as much as possible

            • If zinc salts have been produced on the surface of the H06-4 epoxy zinc-rich antirust paint, use a sweep-grade blasting or mechanical de-rusting method to remove all zinc before painting the primer. Salt and dirt

It is recommended to spray the coating a few Road no air, dry film thickness 50-80mm, brush or roller to be painted 2-3 Road.

H53-32 epoxy zinc phosphate antirust paint, H53-33 epoxy aluminum tripolyphosphate antirust paint, 546 epoxy epoxy antirust paint, Epoxy asphalt super-thick antirust paint, 846 epoxy asphalt thick-type anti-rust paint, chlorinated rubber antirust paint or these types of finish.

But not with oily, alkyd, polyester paint used in supporting.

Surface treatment

              * There are oxide steel: sandblasting to Sa2.5 level, surface roughness 30-75mm. Or pickling treatment to remove all the oxide scale, rust, and a thorough neutralization, washing and passivation

              · No oxide steel: sandblasted to Sa2.5 level, or pneumatic or electric flexible grinding wheel grinding to St3 level

              · Coat shop primer steel: paint film damage, rust and zinc powder on the white rust at the second rust, remove the white rust and polished to St3 level

Construction conditions

• Substrate temperature must be above 3 ℃ above dew point

· When the outdoor construction temperature is lower than 5 ℃, the reaction between the epoxy and the curing agent stops, not suitable for construction.

· Relative humidity not more than 85%

Coating method

Airless spray

          Diluent 103 Diluent

          Dilution 0-10% (by weight of paint)

          Nozzle diameter 0.4-0.5mm

          The discharge pressure was 15 to 17 MPa (about 150 to 170 kg / cm2)

Air spraying

          Large-area construction is not recommended, only for small-sized repair or small coated parts

          Diluent 103 Diluent

          Dilution 0-10% (by weight of paint)

          Nozzle diameter of 2.0-3.0mm

          Air pressure 0.3-0.6MPa (3-6kg / cm2)

Roll coating / brushing

              Diluent 103 Diluent

              Dilution 0-5% (by weight of paint)

              Cleaning agent 103 Thinner

Safety precautions Refer to the MSDS.

Packing group A (base material) 20L barrels 32.5kg

                 Part B (curing agent) 4L Bottled 3.2kg

Shelf life of 12 months

Precautions 

• The drying and curing times of epoxy zinc-rich antirust paint are shortened as the temperature increases.

Curing time at different temperatures are as follows:

· The temperature between 5-10 ℃ can be H06-4 epoxy zinc-rich anti-corrosion paint construction, but the curing speed is very slow

· When the temperature is lower than 5 ℃, it is not suitable for epoxy resin and curing agent to stop. In this case, the temperature can be higher than 5 ℃ in the paint shop for construction, or use H06-4 winter-type epoxy zinc-rich anti-rust paint

• Adequate ventilation is required during the construction and curing of H06-4 epoxy zinc-rich antirust paint

Remark For the correct use of our products, please carefully read the "User's Guide" in this manual.

Statement The above data and data are based on our test and practical experience in the use of accumulated and can be used as construction guide. We do not understand the situation in the construction, we only guarantee the quality of the paint itself, other issues will not be responsible. For this manual, we will be based on the continuous improvement of products have the right to modify.