Composed of epoxy resin, polyamide curing agent, aluminum tripolyphosphate, red iron oxide, such as pollution-free anti-rust paint, additives and solvents composed of two-component epoxy anti-rust paint.

Key Features

· The use of pollution-free anti-rust paint is conducive to environmental protection

· Film has excellent water resistance and seawater resistance and salt spray resistance.

· Tough film has excellent adhesion and impact resistance.

* Film has good oil resistance and solvent resistance.

With epoxy, polyurethane and other topcoats have a good supporting performance.

· Film has good anti-rust performance and durability.

Uses Applicable to steel structures such as ports, docks, heavy machinery, mining machinery, electric power machinery, water conservancy projects, and steel structures above the waterline of ships.

Appearance iron red, gray

Construction parameters

              Volume of solid 54 ± 3% (according to GB / T9272 eqv ISO3233: 1998 requirements) (after mixing)

              Part A: Part B = 26: 3 (weight ratio)

              Dry film thickness 50mm

              Wet film thickness 93mm

              Theoretical amount of 140g / m2

              A flash point of 27 ℃

                             Group B 27 ℃

              Drying time (25 ℃)

                          Table dry ≤ 2h

                          Hard work ≤ 24h

                          Fully cured 7d

Curing time (after mixing) (20 ° C) 30 min

Available time (after mixing)

Overcoating interval time

It is recommended that the number of coating airless spray 1-2 Road or brush, roller 2, dry film thickness greater than 80mm.

Before the road supporting paint H06-4 epoxy zinc-rich anti-rust paint, E06-1 inorganic zinc silicate antirust paint, or direct painting in the derusting quality to Sa2.5 level steel surface.

After the road supporting paint to 842 epoxy cloud iron antirust paint for the middle layer paint, or epoxy type finish, polyurethane topcoat.

Surface treatment

              * There are oxide steel: sandblasting to Sa2.5 level

              * No oxide steel: sandblasting to Sa2.5 level or to the abrasive wheel grinding to St3 level

              • Steel coated with shop primer: sandblasted or sanded with a flexible grinding wheel to St3 level

              · Welding, flame cutting or firework correction Burning parts: remove welding slag, splash, polished smooth, with elastic grinding wheel to St3 level

Construction conditions

              • Substrate temperature should be above 3 ℃ above dew point

              · When the temperature is lower than 5 ℃, curing reaction of epoxy and curing agent is stopped, so it is not suitable for outdoor construction

              · Relative humidity not more than 85%

Coating method

Airless spray

          Diluent 103 Diluent

          Dilution 0-5% (by weight of paint)

          Nozzle diameter 0.4-0.5mm

          The discharge pressure is 20 to 25 MPa (about 200 to 250 kg / cm2)

Air spraying

          Diluent 103 Diluent

          Dilution 0-10% (by weight of paint)

          Nozzle diameter of 2.0-3.0mm

          Air pressure 0.3-0.4MPa (about 3-4kg / cm2)

Roll coating / brushing

              Diluent 103 Diluent

              Dilution 0-3% (by weight of paint)

Cleaning agent 103 Thinner

Safety precautions Refer to the MSDS.

Packaging a group of 20L barrels 26kg

                 Group B is packed in 3L in 4L

Shelf life of 12 months

Remark For the correct use of our products, please carefully read the "User's Guide" in this manual.

Statement The above data and data are based on our test and practical experience in the use of accumulated and can be used as construction guide. We do not understand the situation in the construction, we only guarantee the quality of the paint itself, other issues will not be responsible. For this manual, we will be based on the continuous improvement of products have the right to modify.