<address id="9hx9l"></address>
      <form id="9hx9l"></form>
        <form id="9hx9l"></form>

        <form id="9hx9l"></form>

          Back

          Colored epoxy finish

          Product introduction

          Form :
          Main characteristics :
          Purpose :
          Appearance :

          composition
          Epoxy resin, polyamide curing agent, titanium dioxide, coloring pigments, physical pigments, additives and solvents composed of two-component epoxy finish.

          Key Features

                        * High solids content, can be made of thick film epoxy paint

                        Tough film has excellent adhesion, flexibility, wear resistance and impact resistance and other physical properties

                        Excellent alkali resistance

                        * Has good water resistance and salt water resistance

                        Excellent oil resistance and chemical resistance

                        Excellent durability and corrosion resistance

                        Weather resistance slightly worse, after prolonged exposure, the surface will be slightly chalking, affecting the appearance; but little effect on the protection

          Uses

          For epoxy zinc-rich primer and epoxy iron-iron antirust paint intermediate layer as the protection of high-performance steel structure supporting paint finish, contact with alkaline gas steel structure, reinforced concrete surface and sink, oil tank Floating roof, etc. for high-performance protective coating purposes.

          Appearance and construction parameters  

          product code

          Exterior

          Volume solids* %

          Dry film thicknessm

          Wet film thicknessm

          Theoretical consumption g/m2

          09-31

          Iron oxide red

          553

          50

          91

          122

          09-65

          Light gray

          553

          50

          91

          122

          09-67

          In the yellow

          553

          50

          91

          122

          09-84

          Dark gray

          553

          50

          91

          122

          09-110

          Light sea blue

          553

          50

          91

          122

          * Volume solids (measured according to ISO / IEC 3233: 1998) (after mixing)

          Component A: Component B = 5: 1 (weight ratio)

          A flash point of 27

                        Group B 27

          Drying time (25 )

          Table dry 8h

          Hard work 24h

          Fully cured 7d

          Curing time (after mixing) (20 C) 30 min

          Pot life (after mixing) (20 ) 8h

          (When the temperature is above 30 , the pot life of the mixture of A and B will be shortened with the increase of temperature)

          Overcoating interval time

          temperature

          5

          20

          30

          The shortest

          48h

          24h

          16h

          longest

          14d

          7d

          5d

          It is recommended to coat the number of coating 2, dry film thickness of 100m, brush or roller to be painted 3.

          The former road supporting paint H06-4 epoxy zinc-rich anti-rust paint for the primer, 842 epoxy cloud iron antirust paint for the middle layer paint, or other two-component epoxy antirust paint.

          Surface treatment

                         • Before the paint should be completely dry

                         • Remove all oil and debris from the paint film

          Construction conditions

                         • Substrate temperature should be above 3 above dew point

                          When the temperature is lower than 5 , epoxy reaction with the curing agent stopped, not suitable for outdoor construction. If it is necessary to continue construction without this condition, it shall be disposed of indoors or in a tent, heated surface or forced air drying with hot air.

                          Relative humidity not more than 85%

          Coating method

          Airless spray

                      Diluent 103 Diluent

                      Dilution 0-5% (by weight of paint)

                      Nozzle diameter 0.4-0.5mm

                      The discharge pressure is 10 to 30 MPa (about 150 to 300 kg / cm2)

          Air spraying

                      Diluent 103 Diluent

                      Dilution 0-5% (by weight of paint)

                      The nozzle diameter is 2.0-2.5mm

                      Air pressure 0.3-0.5MPa (about 3-5kg / cm2)

          Roll coating / brushing

                      Diluent 103 Diluent

                      Dilution 0-3% (by weight of paint)

          Cleaning agent 103 Thinner

          Safety precautions Refer to the MSDS.

          Packaging a group of 20L barrels 17kg

                            Group B 4L barrel 3.4kg

          Shelf life of 12 months

          Remark For the correct use of our products, please carefully read the "User's Guide" in this manual.

          Statement The above data and data are based on our test and practical experience in the use of accumulated and can be used as construction guide. We do not understand the situation in the construction, we only guarantee the quality of the paint itself, other issues will not be responsible. For this manual, we will be based on the continuous improvement of products have the right to modify.


          If you have questions, you can

          Or leave a message for us.

          Related recommendation
          Online Service

          Hotline

          0550-7911368

          在线电影播放,奇米第四包,日本一区二区精品视频,一级按摩片A一级按摩

              <address id="9hx9l"></address>
              <form id="9hx9l"></form>
                <form id="9hx9l"></form>

                <form id="9hx9l"></form>