composition

Two-component urethane-based topcoat based on aliphatic isocyanates and hydroxyl-containing acrylic resins, titanium dioxide, color pigments, auxiliaries and solvents.

Key Features

              · Excellent weather resistance and durability

              · Excellent gloss retention and color retention

              · Tough film, good gloss

              * Not easy to powder, yellowing, decorative good

              · Good chemical resistance and water resistance

              * Resistant to mineral oil, vegetable oil, petroleum solvents and petroleum products

              · Good impact resistance and abrasion resistance

Uses

Applicable to high-end products such as large-sized vehicles, railway cars, locomotives, yachts, ships, docks, bridges, machine tools, food machinery and other high-performance products, steel structure or aluminum alloy surface.

The appearance of colored light or matte

Construction parameters

              Volume of solid 52 ± 3% (according to GB / T9272 eqv ISO3233: 1998 provisions) (after mixing)

              Component A: Component B = 8: 1 (weight ratio)

              The dry film thickness is 40 μm

              Wet film thickness of 77μm

              Theoretical amount of 92g / m2

              A flash point of 25 ° C

              Drying time (25 ℃)

              Refers to the dry ≤ 2h

              Hard work ≤ 24h

              Fully cured 7d

Curing time (after mixing) (25 ℃) 30min

Pot life (after mixing) (25 ℃) 6h

Overcoating interval (25 ℃)

 The shortest 16h

The maximum is unlimited

It is recommended that the number of coating channels 2, dry film thickness 80μm.

Before the Road supporting the use of paint 842 Epoxy Manganese Iron Antirust Paint or H53-31 iron red epoxy antirust paint, H53-32 epoxy zinc phosphate antirust paint, polyurethane primer.

Surface treatment

              · Before the paint film must be dry

              · Remove the dirt, dust and other dirt on the film before the film, no acid and alkali and water condensation

Construction conditions

              · When the temperature is below 0 ℃, it is not suitable for outdoor construction

              • Substrate temperature should be above 3 ℃ above dew point

              · Relative humidity less than 75%

Coating method

Airless spray

          Thinner 110 Thinner

          Dilution 0-5% (by weight of paint)

          The nozzle diameter is 0.2-0.4mm

          The discharge pressure is 15 to 20 MPa (about 150 to 200 kg / cm2)

Air spraying

              Thinner 110 Thinner

              Dilution 0-10% (by weight of paint)

              The nozzle diameter is 2.0-2.5mm

              Air pressure 0.3-0.4MPa (about 3-4kg / cm2)

Roll coating / brushing

              Thinner 110 Thinner

              Dilution 0-3% (by weight of paint)

Cleaner 110 Thinner

Safety precautions Refer to the MSDS.

Packing Group A 20L barrel 20kg

                Group B: 2.5L in 4L drums

Shelf life of 12 months

Group B for 6 months

Precautions 

· Before use, pour into the group A, or according to the required ratio of deployment, with how much with the number, mix well after use, and within 6 hours after the preparation of finished

• Tools used during construction must be dry and clean

· The surface to be painted must be clean, no water, no acid and alkali

· It is strictly forbidden to contact with water, acid, alkali and alcohol during the process of paint and coating. Component B can easily react with water, alcohol, etc., with paint after the remaining part of Group B must be tightly sealed barrels, so as to avoid moisture caused by cement loss

In order to make the A and B components fully cross-linked and cured completely, with paint after 25 ℃ in the temperature curing 30min before painting. Temperature below 25 ℃ can be appropriate to extend the aging time

· The paint is not subject to the longest painting interval limit, completely cured without sandpaper to be able to fight the second finish painting

· Construction and drying The relative humidity during solidification shall not be more than 75%, otherwise it will cause serious film blistering

· When the temperature is below 0 ℃, the curing reaction is stopped, so it is not suitable for outdoor construction

· This product must be cured after coating 7 days before delivery

Remark For the correct use of our products, please carefully read the "User's Guide" in this manual.

Statement The above data and data are based on our test and practical experience in the use of accumulated and can be used as construction guide. We do not understand the situation in the construction, we only guarantee the quality of the paint itself, other issues will not be responsible. For this manual, we will be based on the continuous improvement of products have the right to modify.